Krypt Pro3 T-Top Installation Guide

Krypt Pro3 T-Top Installation Guide for DIY Boaters

Click To Download PDF - Krypt Pro3 T Top Installation Guide

Installing the Krypt Pro3 T-Top is one of the best upgrades for boat owners seeking shade, durability, and a professional look. This boat T-Top setup is designed for DIY enthusiasts who want a straightforward process without sacrificing strength or style.

The Krypt Pro3 T-Top installation begins with positioning the side frames evenly on the deck, ensuring proper alignment with the console. Stand-offs provide additional support, keeping the structure secure during rough waters. Once the side sections are assembled, the canopy frame attaches easily, using clamps and marine-grade hardware. Applying threadlocker and sealant ensures long-term stability and prevents stress cracks in the fiberglass.

A key step in this marine canopy installation is lacing the canvas tightly across the frame. Using zip ties for initial tension makes the process simple, while the rope finish provides a clean, professional appearance. The result is a sturdy, foldable T-Top that enhances both function and aesthetics.

For boaters passionate about DIY boating accessories, the Krypt Pro3 offers a balance of performance and ease. With proper installation, this T-Top delivers lasting protection, improved resale value, and a sleek profile that complements any vessel.

Parts List

Make sure all parts are present before beginning.

Front Top Frame ×1
Back Top Frame ×1
Accessory Plates ×2
Center Plate ×1
Side Frames (Port ×2, Starboard ×2)
Stand-offs ×2
Canvas ×1
Rope ×1
Keys ×2
Hardware: M12 bolts ×14, 1/4" bolts ×12, washers, nuts

Before You Begin

Lay out all parts on a tarp/cardboard to prevent scratches.
Apply grease to bolts before installation.
Have a helper available.
Side legs are mirror images (port & starboard). They hinge in the center for folding.
Canopy frame has four sections with hinges for folding/storage.

Step-by-Step Installation

Step 1: Position Side Sections

Place lower halves of side sections on deck.
Ensure equal distance from boat sides and aft.
Consider stand-off placement (1–7 inches from console).

Step 2: Mark Mounting Feet

Use masking tape on deck.
Mark foot positions with a marker (do not mark directly on deck).

Step 3: Assemble Side Sections

Assemble port and starboard sides.
Use threadlocker on bolts.

Step 4: Measure Width

Measure width between marked mounting locations.
Use this measurement to align canopy frame.

Step 5: Assemble Front Top

Attach accessory plate + center plate with 1/4" bolts, washers, and nuts.

Step 6: Assemble Rear Top

Attach accessory plate + center plate.
Do not connect front and rear yet.

Step 7: Attach Canopy to Side Sections

Assemble canopy to side sections on land.
Walk assembly onto boat and place in marked location.
Clamp tips:
1. Thread one bolt per clamp first, then add others before tightening.
2. Cut rubber insert in half if clamp is tight.
3. Use longer bolt temporarily to close clamp, then replace with short bolt.

Step 8: Position Assembly

Lower T-Top over console.
Align mounting feet with marked deck positions.

Step 9: Drill Mounting Holes

Drill pilot holes with small bit.
Remove T-Top, enlarge holes to 0.15" diameter.
Countersink gelcoat to prevent cracks.

Step 10: Seal & Fasten

Remove masking tape.
Apply marine-grade sealant (e.g., 3M 5200).
Lower T-Top into place.
Install screws and tighten feet.
Wipe excess sealant.

Step 11: Mount Rear Canopy Section

Attach rear canopy frame to front.

Step 12: Secure with Threadlocker

Apply threadlocker to bolts.

Step 13: Install Canvas

Use zip ties to hold canvas in place.
Create corner tension with zip ties.

Step 14: Lace Canvas

Tie knots at each end of cord.
Lace canvas tightly across frame.

Final Check

Ensure all bolts are tightened.
Verify canopy tension.
Confirm stand-offs are secure.
Test folding mechanism.